Error 0x80070570 occurs regularly when installing Windows 7. There are numerous suggestions on the Internet to solve this problem, some of them are time consuming, how to run memtest, which takes a couple of hours. Do not worry, if it doesn't. I don't know what memtest is, we will do it. In this guide, I'll start with the easiest methods, you start with the method 1 and stops where it worked.
Method 1: try the installation again (0x80070570)
While the installation is in progress, and this error appears »0x80070570» press OK and go back to the previous screen, start the installation procedure again and redo the installation procedure without rebooting. Try this like 3-4 times, since I know it worked for some. If the error does not reappear, can stop at this method.
Method 2: get out your ram
If you only have one memory card, continue with METHOD 3, but if you have more than one, try removing one at the same time. EG: If you have 4 DDR2 STICKS, tire 1, later try, then roll up the other and test, then roll up the other and test until it works, if none works, return everything and proceed to METHOD 3 – It works, so the one that didn't work is faulty. Despite this, must have 2GB at all times. Si tiene sticks de 1GB, try with 2 inches; the goal here is to find faulty RAM, Yes, there is.
Method 3: MEM TEST
Now run http://www.memtest.org/ – From that site, you can find the precompiled bootable ISO. You can simply download and start it by writing it to a USB drive or CD drive. You will have to change the boot order.
When you run memtest, this is what the screen will show; if the test fails, you will see a message on the screen.
If you report a memory failure, then the only device you have been using is faulty and needs to be replaced. If that is not the case, continue with Method n. ° 4
Method 4: (Rewrite ISO)
Download the Windows ISO file 7 on another computer and write it to a USB drive. I have a post written about how to do it: create a bootable Windows USB 7 Once this is done, you can boot from USB and try to install it.
Method 5: create the account through a command
When prompted for the error, perform the steps below.
-
Hold down the SHIFT key and press F10 (SHIFT + F10) to open command prompt.
-
Write CD C: Windows system 32 and press Enter (if you are already in system C: Windows 32 or if there is an error, write CD oobe only)
-
Type msoobe and hit Enter
A Windows account creation wizard should now be open in front of you. Follow the instructions on the screen to create a generic user account and then reboot the system. This should fix the error.
Method 6: use MMC
-
Hold down the SHIFT key and press F10 (SHIFT + F10) to open command prompt.
-
MMC type
-
Click File and then select Add / Remove Plugin ...
-
Click on Computer Management
-
Click Add
-
Click Local Computer
-
Click Finish and then press OK
-
Click on Computer Management
-
Choose system tools
-
Choose local users and groups
-
Choose users
-
Double click on Administrator
-
Unmark Account is disabled and select OK
-
Right-click on Administrator and select Determine Password …
-
Choose a password you want
Now restart your computer and it should fix the problem.
Method 7: use the up and down keys
A quick solution for this is to use the up and down keys. When you see the first black screen throughout your PC restart, start pressing the up and down arrow keys on the keyboard.
This doesn't always work, but it is known to solve the problem for a considerable number of users, so it is important to emphasize trying.
Method 8: enable default administrator account
If the above methods did not solve your problem or if you cannot see the option “Local users and groups” in the method 2, this should solve the problem. The option “Local users and groups” not enabled in some versions of Windows, especially in the Home version of Windows 7.
Then, the steps given below are an alternative way to activate the default administrator account
-
Hold down the SHIFT key and press F10 (SHIFT + F10) to open command prompt.
-
Enter network user manager / active: yes and press enter
-
Enter the network administrator password / active user: yes and press enter (Note: replace the “password” with the actual password you want to determine for the default administrator account) (BE NOT SURE ABOUT THIS STEP, CHECK BEFORE SENDING)
-
Restart your computer
